top of page

How Your Starlink Dish Stays Connected (and Why a Clear View of the Sky Matters)

Nov 4
4 min read

If you have ever wondered how a flat dish on your roof keeps you online while the satellites above it race across the sky, you are not alone. It is one of the questions we get asked most. The short answer is that your dish is always surrounded by options, and it is very good at switching between them. The longer answer explains why some homes get a rock solid connection and others get annoying dropouts.

Satellites that never stand still

Traditional satellite TV dishes point at one satellite that sits in a fixed spot above the equator, around 36,000 km away. Starlink is different. Its satellites orbit in low Earth orbit, roughly 550 km up, and they move across the sky quickly. Any single satellite is only overhead for a few minutes before it disappears over the horizon.

That sounds like a problem, but SpaceX has launched thousands of these satellites. From most of the UK, there are usually several Starlink satellites in your dish's view at any one time. As one moves away, others are coming in to take its place.

A dish with no moving parts to aim

Your Starlink dish is a phased array antenna. Instead of physically turning to follow a satellite, it is made up of many small antenna elements that work together to steer a beam electronically. That means it can point its beam at a new satellite almost instantly, without the dish itself moving.

When you first set it up, the dish may tilt itself to its best angle (slightly north here in the UK). After that, the clever bit happens electronically.

One link at a time, switched every 15 seconds

A common belief is that a Starlink dish connects to several satellites at once. The more accurate picture is this: your dish has many satellites in view, and the Starlink network assigns it to one of them, then reassigns it on a regular schedule. Independent researchers measuring Starlink from the UK and elsewhere found that these reassignments happen on a globally synchronised cycle of roughly 15 seconds, run by a central Starlink scheduler.

So rather than holding lots of connections open, the system keeps choosing a good satellite for you from those available, over and over. The more satellites in the sky, the more good choices there are, and the less likely you are to fall into a gap. That is why coverage and reliability have improved as more satellites have been launched, and why laser links between satellites help keep traffic flowing even when a ground station is far away.

How obstructions cause dropouts

Here is the catch. The dish can only use satellites it can actually see. Starlink's own setup guidance says your dish needs a clear view of the sky so it can stay connected with satellites as they move overhead, and that objects such as a tree branch, pole or roof will cause service interruptions.

Imagine the sky above your dish as a big dome. If a tree, chimney, neighbouring building or your own roofline is blocking part of that dome, any satellite passing through that patch is lost to you. If the scheduler has assigned you a satellite that then slips behind the tree, your connection can drop for a moment until you are switched to another. On a video call or in an online game, those moments are very noticeable.

Common culprits include:

  • Trees, especially in spring and summer when the leaves come back

  • Chimneys and TV aerials close to the dish

  • Mounting too low on a wall, so the roof blocks half the sky

  • New buildings or extensions nearby

  • Snow, leaves or debris building up on the dish

The Starlink app has an obstruction map that shows where your dish has had trouble seeing satellites. If you see red areas on it and you are getting interruptions, that is a strong sign the mounting position is the issue, not the service.

Why a professional install helps

Starlink recommends a permanent installation for the best performance and long term reliability, and suggests raising the dish above obstructions with a pole, wall or roof mount where needed. Getting this right is where experience counts.

A good installer will:

  • Check the full field of view before choosing a spot, not just what looks clear from the ground

  • Mount the dish high enough to clear rooflines, chimneys and trees, allowing for future growth

  • Use the right bracket or pole so the dish stays secure in British wind and weather

  • Route and protect the cable neatly so it lasts

  • Check the obstruction map and connection once installed

The result is a dish that can see as much of the sky as possible, which gives the Starlink network the widest choice of satellites to hand you between. More choice means fewer dropouts.

The bottom line

Your Starlink dish does not need to hold several satellites at once to stay reliable. It has many in view, steers electronically and gets switched to a good one every few seconds. What it needs from you is a clear view of the sky. Give it that, and it will do the rest.

Getting dropouts? Our trusted PLEO installers can find the clearest view of the sky for your dish, anywhere in the UK.

Join our community of trusted PLEO installers: https://www.facebook.com/groups/1039014051354251

 
 
 

Comments


Post: Blog2_Post
bottom of page